PLUMBING BASICS: THE FIRST STEP FOR BATHTUB INSTALLATION

Plumbing Basics: The First Step for Bathtub Installation

Plumbing Basics: The First Step for Bathtub Installation

Blog Article

About This

We have noticed this great article pertaining to Tools You Need to Install a New Bathtub listed below on the web and thought it made perfect sense to write about it with you on this site.


Installing A Bathtub
Installing a bath tub isn't specifically rocket science, however it does require solid plumbing, woodworking, as well as often, tiling abilities. Replacing an old bath tub with a new one is also a moderately tough task. If the old tub is conveniently obtainable, the project can move immediately; if you have to open up a wall to eliminate the old bathtub as well as position the new bathtub, the task is a lot harder. In either situation, the job is within a residence handyman's abilities, although you will require an assistant to vacate the old tub and also set in the brand-new one. See to it you have actually certified yourself for the job and fit attempting it. Instead of hiring a contractor to take control of a halfway-completed job, it is better to consider utilizing one prior to you begin. Opportunities are you may require a professional plumber to make tube links.
This article will certainly aid you mount a new bath tub in your restroom if you have actually currently purchased a new bathtub as well as do not need to alter the setup of your previous supply of water pipelines.
Your devices and material checklist ought to consist of the following:
  • New Tub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Blade

  • Tape Measure

  • Pipeline Caps


  • Preparing for the Setup


    First of all, the supporting frame provided with the bath ought to be fitted (if called for) according to the supplier's guidelines. Next, fit the taps or mixer to the tub. When fitting the faucet block, it is very important to see to it that if the tap features a plastic washer, it is fitted between the bathroom as well as the faucets. On a plastic bathroom, it is also reasonable to fit a supporting plate under the taps device to stop strain on the tub.
    Fit the adaptable tap adapters to the bottom of the two faucets using 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet through the hole in the bathroom. Use the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next off, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. See to it you make use of every one of the supplied washers.
    Connect the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach the bottom of the overflow tube in a similar manner.The bath ought to now prepare to be fitted in its final placement.

    Removing Old Touches


    If you need to change old faucets with brand-new ones as a part of your installment, then the first thing you ought to do is separate the supply of water. After doing so, turn on the taps to drain any kind of water continuing to be in the system. The procedure of removing the existing faucets can be fairly troublesome as a result of the restricted access that is commonly the case.
    Utilize a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the taps. Have a fabric prepared for the staying water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been eliminated, utilize the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from transforming throughout this procedure. Once the taps have actually been removed, the holes in the bath/basin will certainly have to be cleaned up of any old securing compound.
    Prior to moving on to fit the brand-new taps, contrast the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the new taps to fit.

    Mounting the Bathtub


    Utilizing the two wooden boards under its feet, position the bathtub in the needed placement. The wood boards are handy in uniformly spreading out the weight of the bath tub over the location of the boards rather than focusing all the weight onto 4 tiny factors.
    The following goal is to make sure that the bath tub is leveled all round. This can be attained by examining the level and changing the feet on the bathtub till the spirit level reads degree.
    To set up faucets, fit all-time low of the furthest flexible tap adapter to the ideal supply pipe by making a compression join; then do the exact same for the various other faucet.
    Turn on the water supply as well as inspect all joints as well as new pipework for leaks and also tighten them if essential. Fill the tub and likewise examine the overflow electrical outlet and the normal outlet for leaks.
    Lastly, repair the bathroom paneling as defined in the producer's user's manual. Tiling and also securing around the bathtub must wait till the bath tub has been utilized at the very least once as this will certainly resolve it into its final position.

    Fitting New Touches


    If the tails of the brand-new taps are plastic, then you will certainly need a plastic adapter to avoid damages to the string. One end of the port fits on the plastic tail of the faucet as well as the other end offers a link to the current supply pipelines.
    If you require to fit a monobloc, then you will require lowering couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipe.
    Next, position the tap in the mounting opening in the bath/basin ensuring that the washers are in place in between the faucet and also the sink. Secure the faucet in position with the maker provided backnut. As soon as the tap is safely in position, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with typical tap ports. The previous type ought to be linked to the tap ends first, tightening up only by hand. The supply pipes can later on be connected to the other end. Tighten both ends with a spanner after both ends have been connected.

    Tiling Around the Tub


    In the location where the bath satisfies the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is necessary as the installation can move sufficient to fracture an inflexible seal, creating the water to permeate the wall surface in between the bathroom and also the tiling, bring about complications with moisture as well as feasible leakages to the ceiling below.
    You can pick from a range of coloured sealants to blend in your components and also installations. They are sold in tubes as well as cartridges, as well as are capable of sealing gaps up to a size of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with twists of drenched newspaper or soft rope. Bear in mind to constantly load the bathtub with water before securing, to allow for the activity experienced when the tub remains in use. The sealer can crack fairly very early if you do not take into consideration this movement prior to sealing.
    Conversely, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise easily readily available on the marketplace. It is a good idea to fit the tiles using water-resistant or water-proof sticky as well as grout.

    Bathtub Installation


    How Important Is A Bathtub To Your Home?


    High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.


    Install Piping Before Tub


    You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.


    Position the Tub


    Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.



    NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.


    Assemble Drain Connections


    Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.


    Place a Pipe For the Shower Head


    First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.


    Attaching Hot and Cold Water Lines


    Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.


    Install the Spout


    Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.



    NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.


    Check For Leaks


    Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.


    estore the Bathroom Wall


    Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.

    https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/


    How to Install a Bathtub: Install an Acrylic Tub and Tub Surround

    I am just very occupied with How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I really hope you enjoyed the entire article. Kindly take a moment to distribute this article if you appreciated it. I treasure reading our article about Tools You Need to Install a New Bathtub .


    Make An Appointment

    Report this page